Virgin PC granules across a full melt-flow range, including UV-stabilized grades, for automotive, electrical, construction and optical applications — backed by 130,000 metric tons of annual capacity.
MATERIALS INSIGHT · GON PLASTICS · 3 NOVEMBER 2026 · 1,210 WORDS · 6 MIN READ
Polycarbonate is asked to do contradictory work. In an optical lens it has to stay clear; in an electrical casing it has to hold its dimensions through heat and load; on a building facade it has to keep its surface through years of sun and rain. No single resin answers all three, which is why a PC portfolio is judged by the width of its melt-flow range and the discipline of its testing rather than by one headline property.
GON Plastics produces virgin polycarbonate with an annual capacity of 130,000 metric tons, covering blow moulding, injection moulding and outdoor end uses across eleven grades. Every grade is tested to ISO standards, so the values printed on a datasheet are the values a converter receives in the next container.
KEY TAKEAWAYS — Eleven grades from low-flow PC-903WB to weather-resistant PC-920UR — Melt volume-flow rate spans 3 to 70 cm³/10 min at 300 °C / 1.2 kg — UV-stabilized grades keep base mechanical performance for outdoor parts — ISO 1133, ISO 306 and ISO 527-1-2 testing behind every grade |
Figure 1. Polycarbonate resin portfolio from GON Plastics, covering virgin granules for blow moulding, injection moulding and outdoor applications.
Versatile Polycarbonate Grades for Different Processing Needs
The portfolio is built around two variables that decide most processing outcomes: melt flow and weathering protection. At the low-flow end sit the grades built for blow moulding; through the middle and top of the range are the injection moulding grades; and running in parallel are three grades that add UV protection without giving up the mechanical character of the base resin.
In concrete terms, the line covers PC-903WB, PC-903RB, PC-907RB, PC-910RB, PC-915RB, PC-910L, PC-920 and PC-970, plus the weather-resistant PC-907UR, PC-910UR and PC-920UR. Melt volume-flow rate ranges from 3 cm³/10 min to 70 cm³/10 min, measured at 300 °C under a 1.2 kg load. That span is wide enough for one converter to run three different machines under a single quality system.
Low-Flow Grades for Blow Moulding
PC-903WB and PC-903RB are formulated for blow moulding gallon bottles and containers. The technical reason is melt strength: the parison must hang from the die head long enough to be cut, transferred and inflated. A melt that flows too freely sags, thins at the top and tears at the pinch-off, so holding flow inside a low band widens the processing window instead of narrowing it.
On a bottle line that shows up as fewer wall-thickness corrections during a run, a more repeatable drop-test result and less scrap at start-up. Both grades share the same base chemistry, and both are supplied as virgin granules, which keeps colour and clarity predictable order after order.
Medium and High Flow Grades for Injection Moulding
Medium and high flow PC resins are aimed at standard injection moulding and thin-wall injection moulding. As wall sections thin out, the melt has less time and less room to fill the cavity before it freezes. Higher flow lets the cavity fill at lower injection pressure, which reduces shear stress and the warpage that follows it in long, flat parts such as panels and covers.
The injection grades in the line — PC-907RB, PC-910RB, PC-915RB and PC-910L — sit inside this band, so a moulder can move a part from a thick section to a thin one without leaving the family or re-qualifying the material. PC-920 and PC-970 serve the high-flow end of the range where the wall is thinnest and the flow path is longest.
UV-Stabilized Grades for Long-Term Outdoor Service
Outdoor polycarbonate fails in a recognisable sequence: surface yellowing first, then crazing, then a loss of impact strength at the edges. PC-907UR, PC-910UR and PC-920UR are modified to slow that sequence while preserving the base mechanical performance. That distinction matters in practice: a UV grade that changed shrinkage behaviour would force every existing mould to be re-qualified, and the material benefit would be paid for twice.
Reliable Performance Verified by ISO Testing Standards
Every grade in the PC line is tested to ISO 1133 for melt flow rate, ISO 306 for Vicat softening temperature and ISO 527-1-2 for tensile strength. The three methods answer three different questions, and a buyer comparing quotations needs all three.
Melt Flow as a Process Control Variable
Melt flow is the first value a processor feels on the machine. It sets the temperature profile, the injection speed and, in thin-wall work, the pressure available at the end of fill. When the value sits where the datasheet says it sits, an existing process recipe keeps working; when it drifts between lots, operators compensate with heat and cycle time, and that compensation becomes a hidden cost carried for the life of the part.
Heat and Mechanical Limits
Vicat softening temperature defines how close a part can run to its thermal ceiling before it deforms under load or in a drying oven. Tensile strength defines how much stress the design can carry and how the part behaves at a joint, a snap-fit or a screw boss. Polycarbonate is valued for heat resistance, high impact strength and good dimensional stability, and the point of testing is to confirm that those properties arrive the same way in every shipment.
Why Repeatability Outranks a Headline Number
A single impressive figure rarely decides a project on its own; repeatability across lots does. Consistent material properties are what let a manufacturer reduce production defects and hold finished-part quality without adding inspection steps that were never quoted. That is the practical meaning of testing every grade rather than sampling a reference batch.
Broad End-Use Applications and Large Production Capacity
Virgin PC granules from this line are used for building panels, automotive exterior and interior parts, electrical and electronic casings, suitcases, tableware and optical lenses. The common thread is not the industry but the requirement: a part that must stay in shape, stay in one piece and keep its surface.
Typical End Uses
(1)Building and construction: solid and multiwall panels where impact resistance and dimensional stability carry more weight than cost per kilogram.
(2)Automotive: exterior and interior parts that must hold shape through heat cycles and resist stone impact.
(3)Electrical and electronic: casings and housings that depend on dimensional stability and a clean surface finish.
(4)Consumer and optical: suitcases, tableware and lenses, where clarity and toughness are the reasons the material is specified at all.
Capacity Behind the Grade List
A wide portfolio is only useful if it can be delivered. The line is supported by 130,000 metric tons of annual polycarbonate production capacity, which allows stable, continuous supply for bulk orders and long-term supply contracts rather than spot allocations. For a converter planning a twelve-month programme, that is the difference between a quotation and a schedule.
Technical support runs alongside supply: full datasheets, formulation consultation and application support for global partners, including guidance on which grade fits a given wall thickness or outdoor exposure.
Choosing a Grade Without Leaving the Family
The selection sequence is short. Start with the process — blow moulding, standard injection moulding or thin-wall injection moulding — and the flow band follows. Then check the service environment: an indoor housing and a facade panel do not need the same weathering protection, and paying for UV stabilization on an internal part is a cost without a benefit. Finally confirm the thermal and mechanical values on the datasheet against the design margin, not against a competitor's brochure.
As a professional virgin polycarbonate manufacturer, GON Plastics supplies the full GON brand PC range from a single production base. Detailed technical datasheets and grade specifications are published on the polycarbonate resin product page and can be cross-checked against our sales team before a trial order is placed.